|
|
|
|
MOTOR SERIES TYPES
|
POWER OPTIONS (HP)
|
MAX SPEED AVAILABLE (RPM)
|
MAX. TOOL CAPACITY
|
SPECIAL FEATURES
|
COLLET & COVERNUT
|
HSK-C
|
HYDRO-CLAMP
|
QUICK CLAMP SYSTEM
|
TECHNICAL SPECS
|
|
|
KN 20
|
0.5 to 1
|
30,000
|
1/2"
|
|
Y
|
N
|
Y
|
Y
|
PDF
|
|
|
KRS 35
|
1 to 3
|
18,000*
|
1/2"
|
*Available in 24,000 RPM
|
Y
|
N
|
N
|
N
|
PDF
|
|
|
KRS 50
|
4 to 6.5
|
18,000
|
5/8"
|
|
Y
|
Y
|
N
|
N
|
PDF
|
|
|
KRSV 51
|
6.5
|
18,000
|
1"
|
|
Y
|
N
|
Y
|
Y
|
PDF
|
|
|
KRS 60
|
9.0
|
18,000
|
3/4"
|
|
Y
|
Y
|
N
|
Y
|
PDF
|
|
|
KRSV 61
|
9.0
|
18,000
|
1"
|
|
Y
|
N
|
Y
|
Y
|
PDF
|
|
|
KN 50
|
4 to 6.5
|
18,000
|
5/8"
|
†HSK-C Optional
|
Y
|
O†
|
N
|
N
|
PDF
|
|
|
KN 60
|
9.0
|
18,000
|
5/8"
|
†HSK-C Optional;
|
Y
|
O†
|
N
|
N
|
PDF
|
|
|
KNO 70
|
10 to 17
|
18,000
|
1"
|
|
Y
|
Y
|
Y
|
Y
|
PDF
|
|
|
VS 50/60
|
2 to 7
|
24,000
|
1/2"
|
|
Y
|
N
|
Y
|
Y
|
PDF
|
|
|
VUS 50/60
|
1 to 3.5
|
24,000
|
1/2"
|
Non-ventilated
|
Y
|
N
|
N
|
N
|
PDF
|
Prints are shown with collet & tool holding. Please contact us for motor prints with alternate tool holding options
|
| TOOL SYSTEMS: |
- Collet & covernut
- HSK-C (Standard and optional as indicated in chart)
- Hydro-damp chuck system (ETP HydroGrip) on selected models
- Quick clamping system
- Cylindrical shaft with or without key
- Cylindrical shaft with or without key and outside thread
- Cylindrical shaft with or without key and inside thread
- Saw blade flanges and nut available
- External or internal taper
|
| FREQUENCY: |
- 60 to 500 HZ (3,600 to 30,000 RPM)
- Electrical performance data (HP) are only valid for the stated constant frequency
|
| VOLTAGE: |
- 230/400V standard according to DIN/VDE regulations; however, other voltage options are available
- Insulation class F standard
- If using a static frequency converter, it is necessary to use line reactors or filters to smooth out the sine wave
|
| BEARINGS: |
- Lifetime lubricated, high precision bearings (where required)
- Drive end bearing is fixed and non-drive end bearing is self-aligning
- With heavy tooling, double bearing arragements are recommended for front bearing position to eliminate axial shaft play
|
| FEATURES: |
- TEFC motors are self-ventilated with a built in fan which works most effectively at the motor's maximum operating speed
- Labyrinth seals at both ends of the motor to protect against dust or particle penetration into the motor when under power
- Motors are balanced to a vibration speed of Veff = 1.8 mm/sec at zero load and rated operating speed
- Most motors are available according to NEMA or CSA standards (L.R. 16 865)
|
|
